Hardware Issues

3.1 Minimal configuration

The following is probably the smallest possible configuration that Linux will work on: 386SX/16, 1 MB RAM, 1.44 MB or 1.2 MB floppy, any supported video card (+ keyboards, monitors, and so on of course). This should allow you to boot and test whether it works at all on the machine, but you won't be able to do anything useful. See http://rsphy1.anu.edu.au/~gpg109/mem.html for minimal Linux configurations

In order to do something, you will want some hard disk space as well, 5 to 10 MB should suffice for a very minimal setup (with only the most important commands and perhaps one or two small applications installed, like, say, a terminal program). This is still very, very limited, and very uncomfortable, as it doesn't leave enough room to do just about anything, unless your applications are quite limited. It's generally not recommended for anything but testing if things work, and of course to be able to brag about small resource requirements.

3.2 Usable configuration

If you are going to run computationally intensive programs, such as gcc, X, and TeX, you will probably want a faster processor than a 386SX/16, but even that should suffice if you are patient.

In practice, you will want at least 4 MB of RAM if you don't use X, and 8 MB if you do. Also, if you want to have several users at a time, or run several large programs (compilations for example) at a time, you may want more than 4 MB of memory. It may still work with a smaller amount of memory, but it will use virtual memory (using the hard drive as slow memory) and that will be so slow as to be unusable. If you use many programs at the same time, 16 MB will reduce swapping considerably. If you don't want to swap appreciably under normal load, 32 MB will probably suffice for a single user. If you run lots of memory-intensive applications at once, 64 MB may be necessary to avoid lots of swapping. Of course, if you run memory-hungry applications, you may want more.

The amount of hard disk you need depends on what software you want to install. The normal basic set of Unix utilities, shells, and administrative programs should be comfortable in less than 10 MB, with a bit of room to spare for user files. For a more complete system, get Red Hat, Debian, or another distribution, and assume that you will need 60 to 600 MB, depending on what you choose to install and what distribution you get. Add whatever space you want to reserve for user files to these totals. With today's prices on hard drives, if you are buying a new system, it makes no sense to buy a drive that is too small. Get at least 2 GB, preferably 4 GB or more, and you will not regret it. Linux will happily handle very large hard drive such as the recently popular 11 GB IDE hard drives or 18 GB SCSI hard drives.

Add more memory, more hard disk, a faster processor and other stuff depending on your needs, wishes and budget to go beyond the merely usable. In general, one big difference from DOS is that with Linux, adding memory makes a large difference, whereas with DOS, extra memory doesn't make that much difference. This of course has something to do with DOS's 640KB limit, which is completely nonexistent under Linux.

3.3 Supported hardware

CPU:

Anything that runs 386 protected mode programs. All models of 386s 486s, Pentiums, Pentium Pros, Pentium IIs, and clones of these chips should work. (286s and below may someday be supported on a smaller kernel called ELKS (Embeddable Linux Kernel Subset), but don't expect the same capabilities). A version for the 680x0 CPU (for x = 2 with external MMU, 3, 4, and 6) which runs on Amigas and Ataris can be found at tsx-11.mit.edu in the 680x0 directory. Many DEC Alphas, SPARCs, and PowerPC machines are supported. Ports are also being done to the ARM, StrongARM, and MIPS architectures. More details are available elsewhere.

Architecture:

PCI, ISA, EISA, and VLB busses. MCA (mostly true blue PS/2s) support is incomplete but improving (see above). Linux puts higher demands on hardware than DOS, Windows, and in fact most operating systems. This means that some marginal hardware that doesn't fail when running less demanding operating system may fail when running Linux. Linux is an excellent memory tester...

RAM:

Up to 1 GB on Intel; more on 64-bit platforms. Some people (including Linus) have noted that adding ram without adding more cache at the same time has slowed down their machine extremely, so if you add memory and find your machine slower, try adding more cache. Some machines can only cache certain amounts of memory regardless of how much RAM is installed (64 MB is the most one popular chipset can cache). Over 64 MB of memory will require a boot-time parameter with kernels 2.0.35 and earlier, as the BIOS was originally designed to be unable to report more than 64MB. Recent 2.1.x kernels and later are able to detect more memory in a system.

Data storage:

Generic AT drives (EIDE, IDE, 16 bit HD controllers with MFM or RLL, or ESDI) are supported, as are SCSI hard disks and CD-ROMs, with a supported SCSI adaptor. Generic XT controllers (8 bit controllers with MFM or RLL) are also supported. Supported SCSI adaptors: Advansys, Adaptec 1542, 1522, 1740, 27xx, and 29xx (with some exceptions) series, Buslogic MultiMaster and Flashpoint, NCR53c8xx-based controllers, DPT controllers, Qlogic ISP and FAS controllers, Seagate ST-01 and ST-02, Future Domain TMC-88x series (or any board based on the TMC950 chip) and TMC1660/1680, Ultrastor 14F, 24F and 34F, Western Digital wd7000, and others. SCSI, QIC-02, and some QIC-80 tapes are also supported. Besides IDE and SCSU cdroms, several proprietary CD-ROM devices are also supported, including Matsushita/Panasonic, Mitsumi, Sony, Soundblaster, Toshiba, ATAPI (EIDE), SCSI, and others. For exact models, check the hardware compatibility HOWTO. N.B. These lists are incomplete, and always will be. Distribution vendors maintain more up-to-date lists.

Video:

VGA, EGA, CGA, or Hercules (and compatibles) work in text mode. For graphics and X, there is support for (at least) normal VGA, some super-VGA cards (most of the cards based on Tseng, Paradise, and some Trident chipsets), S3, 8514/A, ATI, Matrox, and Hercules. (Linux uses the XFree86 X server, so that determines what cards are supported. A full list of supported chipsets alone takes over a page. See http://www.XFree86.org/)

Networking:

Ethernet support includes 3COM 503/509/579/589/595/905 (501/505/507 are supported but not recomended), AT&T GIS (neé NCR) WaveLAN, most WD8390-based cards, most WD80x3-based cards, NE1000/2000 and most clones, AC3200, Apricot 82596, AT1700, ATP, DE425/434/435/500, D-Link DE-600/620, DEPCA, DE100/101, DE200/201/202 Turbo, DE210, DE422, Cabletron E2100 (not recommended), Intel EtherExpress (not recommended), EtherExpress Pro, EtherExpress 100, DEC EtherWORKS 3, HP LAN, HP PCLAN/plus, most AMD LANCE-based cards, NI5210, ni6510, SMC Ultra, DEC 21040 (tulip), Zenith Z-Note ethernet, All Zircom cards and all Cabletron cards other than the E2100 are unsupported, due to the manufacturers unwillingness to release programming information freely.

FDDI support currently includes the DEFxx cards from DEC.

Point-to-Point networking support include PPP, SLIP, CSLIP, and PLIP. PPP support is available for both standard asyncronous devices like modems, and syncronous connections like ISDN.

Limited Token Ring support is available.

Serial:

Most 16450 and 16550 UART-based boards, including AST Fourport, the Usenet Serial Card II, and others. Intelligent boards supported include Cyclades Cyclom series (supported by the manufacturer), Comtrol Rocketport series (supported by the manufacturer), Stallion (most boards; supported by the manufacturer), and Digi (some boards; supported by the manufacturer). Some ISDN, frame relay, and leased line hardware is supported.

Other hardware:

SoundBlaster, ProAudio Spectrum 16, Gravis Ultrasound, most other sound cards, most (all?) flavours of bus mice (Microsoft, Logitech, PS/2), etc.

<< Previous  Next >>